<noframes id="mnwke"><bdo id="mnwke"><delect id="mnwke"></delect></bdo><noframes id="mnwke"><delect id="mnwke"></delect><noframes id="mnwke"><noframes id="mnwke"><rt id="mnwke"><delect id="mnwke"><delect id="mnwke"></delect></delect></rt><noframes id="mnwke"><delect id="mnwke"><rt id="mnwke"></rt></delect><rt id="mnwke"></rt><noframes id="mnwke"><noframes id="mnwke"><bdo id="mnwke"><rt id="mnwke"></rt></bdo><noframes id="mnwke"> <bdo id="mnwke"><rt id="mnwke"></rt></bdo><noframes id="mnwke"><delect id="mnwke"></delect><noframes id="mnwke"><noframes id="mnwke"><rt id="mnwke"></rt><noframes id="mnwke"><noframes id="mnwke"><noframes id="mnwke"><rt id="mnwke"><rt id="mnwke"></rt></rt> <rt id="mnwke"></rt><noframes id="mnwke"><rt id="mnwke"></rt><delect id="mnwke"></delect><bdo id="mnwke"></bdo><noframes id="mnwke"><delect id="mnwke"><rt id="mnwke"></rt></delect><bdo id="mnwke"></bdo><noframes id="mnwke"><bdo id="mnwke"><rt id="mnwke"></rt></bdo><noframes id="mnwke"><noframes id="mnwke"><rt id="mnwke"><rt id="mnwke"></rt></rt><noframes id="mnwke"><delect id="mnwke"></delect><rt id="mnwke"><rt id="mnwke"><delect id="mnwke"></delect></rt></rt><noframes id="mnwke"><rt id="mnwke"></rt><noframes id="mnwke"><delect id="mnwke"><rt id="mnwke"></rt></delect><noframes id="mnwke">
歡迎來到濟南榮凱升降機械有限公司官網!

收藏本站 | 設為首頁 | 移動式升降機 | 導軌式升降機 | 剪叉式升降機| 聯系我們

榮凱機械

多年專注液壓升降機械研發生產

液壓升降機械放心廠家

全國免費服務熱線: 0531-84258899

熱門關鍵詞: 升降機 升降平臺 升降貨梯 套缸式升降機 曲臂式升降機

榮凱升降機械
當前位置:首頁 » 升降貨梯冷卻器安裝方法

升降貨梯冷卻器安裝方法

文章出處:www.utahhomes4all.com 責任編輯:admin 人氣:2984 發表時間:2016-04-05 13:06:32
升降貨梯中的冷卻器一般應安放在回油管或低壓管路上,這樣可防止冷卻器承受高壓且冷卻效果也較好。如溢流閥的出口,系統的主回流路上或單獨的冷卻系統。
Lift manufacturers introduced lift the cooler should normally be placed in the return pipe or low pressure pipeline, which prevents cooler withstand high pressure and the cooling effect is better. Such as the main export reflux relief road system or separate cooling system.

升降貨梯冷卻器所造成的壓力損失一般約為0.0lMPa,液壓系統的加熱一般常采用結構簡單、能按需要自動調節最高和最低溫度的電加熱器。加熱器安裝時用法蘭盤水平安裝在油箱側壁上,發熱部分全部浸在油液內。加熱器應安裝在箱內油液流動處,以有利于熱量的交換。由于油液是熱的不良導體,單個加熱器的功率容量不能太大,以免其周圍油液過度受熱后發生變質現象。
Manufacturers remind you lift the pressure loss caused by the cooler is generally about 0.0lMPa, heating of the hydraulic system is generally often used a simple structure, can be automatically adjusted according to the maximum and minimum temperatures of the electric heater. Heater installation with horizontal flange on the tank side wall portion of all heat soaked in oil. Heater should be installed in the box at the oil flow to facilitate heat exchange. Because oil is a poor conductor of heat, power capacity of a single heater is not too large, in order to avoid deterioration phenomenon occurred after the oil around excessive heat.

 

此文關鍵字:升降貨梯

榮凱快訊新聞排行

升降機知識排行

升降機問答排行

风间中文字幕亚洲一区
<noframes id="mnwke"><bdo id="mnwke"><delect id="mnwke"></delect></bdo><noframes id="mnwke"><delect id="mnwke"></delect><noframes id="mnwke"><noframes id="mnwke"><rt id="mnwke"><delect id="mnwke"><delect id="mnwke"></delect></delect></rt><noframes id="mnwke"><delect id="mnwke"><rt id="mnwke"></rt></delect><rt id="mnwke"></rt><noframes id="mnwke"><noframes id="mnwke"><bdo id="mnwke"><rt id="mnwke"></rt></bdo><noframes id="mnwke"> <bdo id="mnwke"><rt id="mnwke"></rt></bdo><noframes id="mnwke"><delect id="mnwke"></delect><noframes id="mnwke"><noframes id="mnwke"><rt id="mnwke"></rt><noframes id="mnwke"><noframes id="mnwke"><noframes id="mnwke"><rt id="mnwke"><rt id="mnwke"></rt></rt> <rt id="mnwke"></rt><noframes id="mnwke"><rt id="mnwke"></rt><delect id="mnwke"></delect><bdo id="mnwke"></bdo><noframes id="mnwke"><delect id="mnwke"><rt id="mnwke"></rt></delect><bdo id="mnwke"></bdo><noframes id="mnwke"><bdo id="mnwke"><rt id="mnwke"></rt></bdo><noframes id="mnwke"><noframes id="mnwke"><rt id="mnwke"><rt id="mnwke"></rt></rt><noframes id="mnwke"><delect id="mnwke"></delect><rt id="mnwke"><rt id="mnwke"><delect id="mnwke"></delect></rt></rt><noframes id="mnwke"><rt id="mnwke"></rt><noframes id="mnwke"><delect id="mnwke"><rt id="mnwke"></rt></delect><noframes id="mnwke">